Tapping WoodBinder®
Tapping screws that are designed to be used in wood or light gauge metal in a predrilled hole. See Fastener Selection Guide on page 1 for proper drill bit sizes.
Screws can be used as replacements for nails or screws that have loosened from wood or steel.
3/8” HWH with EPDM bonded sealing washer provides maximum pull over strength in high wind uplift applications.
EPDM rubber & HWH with EPDM bonded washer is vulcanized to a steel washer to form an excellent seal & will cover any existing hole to prevent leaks from reoccurring.
| SIZE | POINT STYLE | HEAD STYLE | CARTON QTY. | WEIGHT/M |
|---|---|---|---|---|
| 14 x 3/4″ | TYPE A | 3/8″ HWH | 2500 | 16.5 |
| 14 x 1″ | TYPE A | 3/8″ HWH | 2000 | 16.9 |
| 14 x 1-1/4″ | TYPE A | 3/8″ HWH | 2000 | 17.6 |
| 14 x 1-1/2″ | TYPE A | 3/8″ HWH | 1500 | 24.6 |
| 14 x 2″ | TYPE A | 3/8″ HWH | 1500 | 26.0 |
| 14 x 2-1/2″ | TYPE A | 3/8″ HWH | 1000 | 30.8 |
| 14 x 3″ | TYPE A | 3/8″ HWH | 1000 | 35.9 |
| DRILL POINT (DIA) | MAJOR DIAMETER | MINOR DIAMETER | WASHER/HEAD DIAMETER | HEAD ACROSS FLATS | ULT. TENSILE STRENGTH | MIN. TORSIONAL STRENGTH | NOM. SHEAR STRENGTH | |
|---|---|---|---|---|---|---|---|---|
| #14-10 HWH TYPE A | 30º Sharp Point-A | .254/.248 | .185/.178 | .500 | NOM .375″ | 4270 LBS | 125 IN-LBS. | 2997 LBS |
| SUBSTRATE | (1) – 1″ PENETRATION (2) – 1 1/2″ PENETRATION |
(3) – FULL PENETRATION (4) – 1/2″ PENETRATION |
|||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| MATERIAL | |||||||||||||||||
| HRS PRIMED ONLY | 3/4″ PLY | 5/8″ PLY | 1/2″ PLY | 7/16″ OSB | 2X Y. PINE | 2X SPF | |||||||||||
| NOM.GAUGE | 16 | 14 | 12 | ||||||||||||||
| THICKNESS | .060 | .075 | .105 | (3) | (4) | (3) | (4) | (3) | (4) | (3) | (4) | (1) | (2) | (4) | (1) | (2) | (4) |
| #14-10 HWH TYPE-A | 800 | 1250 | 2017 | 723 | N/A | 487 | N/A | 391 | N/A | 227 | N/A | 856 | 1669 | N/A | 594 | 1235 | N/A |
| DESIGNATION | MATERIALS | ||||||
|---|---|---|---|---|---|---|---|
| AZ55 GALVANIZED | G90 | ALUMINUM | SLOT EDGE PANEL | ||||
| NOM. GAUGE | 29 | 26 | 24 | 22 | 20 | 21 | 29 |
| THICKNESS | .014 | .018 | .024 | .030 | .036 | .028 | .014 |
| #14-10 HWH TYPE A(16mm O.D. BONDED WASHER) | N/A | 1001 | 1206 | 1649 | N/A | N/A | N/A |
FOR PROPER INSTALLATION, THE USE OF IMPACT DRIVERS ARE NOT RECOMMENDED FOR POWDER COATED OR ANY WET PAINTED FASTENER.
PULLOUT & PULLOVER VALUES ARE DETERMINED IN THE ST FASTENING SYSTEMS ENGINEERING LABORATORY USING STEEL PANELS/FRAMING & WOOD DENSITIES WHOSE STRUCTURAL PROPERTIES ARE FOUND IN PRESENT DAY PRODUCTS.
ALL STRENGTH VALUES SHOWN ARE ULTIMATE VALUES, EXPRESSED IN LBS. APPLY AN APPROPRIATE SAFETY FACTOR TO OBTAIN DESIGN LIMITS.
